
You can get a quote for carbide scrap without shipping anything first. A buyer needs a description of the material, an approximate weight and a few photographs — and from that can give you a figure before you pack a box or book a collection. What follows is the full sequence from first enquiry to payment, including how material is graded on arrival and what happens if the weighed result differs from your estimate.
Can I get a quote online before shipping anything?
Yes, and you should not accept an arrangement that works any other way. A reputable buyer quotes on a description and photographs, in writing, before the material moves. Carbide Kings returns quotes the same day during business hours.
If a buyer will only give you a number once the material is in their building, you have lost your negotiating position before the transaction starts. That is the single most important thing to know about this process.
What information does a buyer need to quote?
| What to send | Why it matters |
|---|---|
| Material category | Inserts, endmills, rods, dies, wear parts, brazed tooling and sludge are graded and priced differently. Naming them is the largest single improvement you can make to a quote request. |
| Approximate weight | Determines whether you ship, use freight, or arrange collection, and gives both sides a reference point against the weighed figure later. |
| Photographs | Lets the buyer confirm the material class and spot anything unusual before committing to a number. |
| Whether steel is attached | Brazed tooling and saw tips are part carbide, part steel body. Flagging this up front avoids a revised figure later. |
| Condition of sludge or grindings | Moisture, coolant and contamination affect what is recoverable, so this category needs describing rather than just naming. |
| Your location | Decides whether shipping or collection is the sensible route. |
You do not need to know insert grades or cobalt percentages. If you knew those, you would not need the buyer. Send what you can identify and describe the rest plainly.
How should I photograph carbide for a quote?
- Shoot in good light on a plain surface. Phone photographs are fine; a dim shot of a bucket is not.
- Include something for scale — a ruler, a coin, a hand. Carbide is deceptive in photographs because it is small and heavy.
- Take one wide shot showing the whole lot, so the buyer can judge quantity.
- Take a close-up of a representative piece, close enough to see form and surface.
- Photograph any markings, part numbers or grade codes if the material carries them. Not essential, but useful.
- Photograph each material class separately rather than piling everything together. Mixed photographs produce cautious quotes.
- For sludge or grindings, photograph the container as well as the material, so the buyer can see how it is stored.
How do buyers evaluate carbide quality?
Grading is not arbitrary, and understanding the variables makes the eventual figure predictable rather than mysterious.
- Material class. Solid carbide, brazed tooling and sludge or grindings are three different products commercially, even when they arrive in the same box.
- Cobalt binder content. Cemented carbide is tungsten carbide grains held in a cobalt binder, and the proportion varies by grade. Both metals are recovered, so binder content affects value.
- Contamination. Steel components, non-carbide material mixed in, and heavily contaminated sludge all reduce what can be recovered cleanly.
- Consistency of the lot. A lot that is uniformly one material class is assessed with more confidence than one that is mixed, and confidence shows up in the number.
- Form. Solid pieces, turnings and powder behave differently in reclamation and are handled accordingly.
The practical consequence is that blended lots price conservatively. When a buyer cannot tell what proportion of a container is what, they price for the less favourable assumption. Separating material before quoting is the cheapest thing you can do to improve the outcome. For more on how the figure is built, see Carbide Scrap Pricing.
What should I do to prepare the material?
Less than most people assume. Over-preparation is wasted labour, and some of it actively costs you time for no return.
- Separate by class — solid carbide, brazed tooling, sludge and grindings. This is the one preparation step that reliably pays.
- Remove obvious non-carbide items. Steel shanks that have already separated, packaging, and anything that plainly is not carbide.
- Drain free coolant from sludge and grindings, and seal the container. Do not attempt to dry it out.
- Do not degrease or polish anything. A recycler is buying the material, not the appearance, and the labour will not come back to you.
- Do not break down or cut up tooling. Whole endmills, drills and brazed tools are accepted as they are.
- Weigh it if you have scales. Even a rough figure gives you a reference against the verified weight.
What happens after the material arrives?
- Receipt and logging. The lot is booked in against your quote reference, which is why putting that reference inside the box as well as on the label is worth the thirty seconds.
- Sorting and verification. Material is separated into its categories and checked against your description. Anything that is not carbide is identified.
- Weighing. Calibrated scales, by material category rather than as one gross figure.
- Confirmation and payment. The verified figure is confirmed against the quote and payment is issued.
What if the weighed result differs from my estimate?
It usually will, at least slightly, and that is normal. People consistently underestimate carbide weight because it is denser than it looks, so the surprise is more often in the seller's favour than against.
What matters is that a difference in weight is not the same as a change in terms. If you were quoted a rate per pound for a described material, a heavier lot means more money at the same rate. A revised rate is a different matter, and should only happen if the material turns out to be substantially different from what was described — significantly more brazed tooling than stated, or contamination that was not mentioned.
Ask two things before you ship, so neither is a question later. First, that you will see the recorded weights by category rather than a single total. Second, what happens if you decline the final offer — whether the material is returned and who bears that cost.
How and when do I get paid?
Payment follows verification. Where material is collected in person and weighed on site, the assessment is complete at that point and settlement can happen there. Where material is shipped in, payment is issued after it has been received, sorted and weighed.
The full sequence at a glance
| Stage | What you do | What the buyer does |
|---|---|---|
| Enquiry | Send material categories, approximate weight and photographs | Reviews and returns a written quote, same day during business hours |
| Decision | Accept, decline, or ask questions | Confirms terms and the route — ship, freight, or collection |
| Preparation | Separate by class, seal sludge, pack or palletise | Arranges freight or schedules collection where applicable |
| Transit | Ship, or have the lot ready on collection day | Collects or receives the material |
| Verification | Nothing — but ask to see the category weights | Sorts, verifies against description, weighs on calibrated scales |
| Payment | Confirm the final figure | Issues payment |
How do I get a quote from Carbide Kings?
Send your material categories, an approximate weight and photographs through the quote form, or call (980) 515-7064. Quotes are returned the same day during business hours — Monday to Friday, 8:00 AM to 5:00 PM, and Saturday, 10:00 AM to 2:00 PM Eastern.
Carbide Kings is a BBB-accredited tungsten carbide buyer based in Charlotte, North Carolina, buying across all fifty states with no minimum quantity. Material can be shipped to the receiving facility at 15330 Scholastic Dr, Charlotte, NC 28277, or collected for larger commercial lots.
Related reading: what we accept, selling small quantities, and how collection works for industrial lots.
Frequently asked questions
Can I get a quote online from tungsten carbide scrap buyers?
Yes. A quote is normally given from a description of the material, an approximate weight and photographs, before anything is shipped. Carbide Kings returns quotes the same day during business hours. A buyer who will only quote once the material is in their possession should be treated with caution.
What information do I need to get a carbide scrap quote?
The material categories you have, an approximate weight, photographs, whether any of it is brazed tooling with a steel body, and your location. You do not need to know insert grades or cobalt percentages — describe what you can identify and let the buyer assess the rest.
How do tungsten carbide scrap buyers evaluate material quality?
By material class, cobalt binder content, contamination, consistency of the lot and physical form. Solid carbide, brazed tooling and sludge are three commercially different products even in the same box, which is why mixed lots are quoted more conservatively than sorted ones.
Do I need to clean or prepare carbide scrap before selling it?
Separate it by class and drain free coolant from sludge, and stop there. Degreasing, polishing and breaking down tooling are wasted labour — a recycler is buying the material, not the appearance, and worn or damaged tools are accepted as they are.
What happens if the actual weight differs from my estimate?
A weight difference is normal, because carbide is denser than people estimate by eye, and it is more often in the seller's favour. At an agreed rate per pound, a heavier lot simply means more money. A revised rate is a separate matter and should only apply if the material turns out to be substantially different from the description.
How long does it take to get paid for carbide scrap?
Payment follows verification. Where material is weighed on site during a collection, settlement can happen at that point. Where it is shipped in, payment is issued after receipt, sorting and weighing on calibrated scales.
Have tungsten carbide scrap to sell?
Contact Carbide Kings for a fast quote on your carbide scrap.
